314 lines
11 KiB
TeX
314 lines
11 KiB
TeX
\chapter{FRU REMOVAL AND REPLACEMENT PROCEDURES}
|
|
\setcounter{page}{1}
|
|
|
|
\section{Introduction}
|
|
This chapter describes the removal and replacement procedures for the
|
|
field replaceable units (FRUs). To use this chapter, find the name of the
|
|
FRU that needs replacing in \tabref{3-1} then go to the section listed beside
|
|
the FRU. Follow the steps in the section to remove the FRU and reverse
|
|
the procedures to replace the FRU.
|
|
|
|
\begin{tbl}{FRU Section Listings}{l l l}
|
|
\textbf{FRU} & \textbf{Section} & \textbf{Page} \\
|
|
\hline
|
|
|
|
Battery pack & \hyperlink{section.3.10}{3.10} & 3-33 \\[0.5em]
|
|
DEC423 Converter (MicroVAX 2000 only) & \hyperlink{subsection.3.15.1}{3.15.1} & 3-53 \\[0.5em]
|
|
Expansion adapter & \hyperlink{section.3.16}{3.16} & 3-54 \\[0.5em]
|
|
Expansion adapter disk interface module & \hyperlink{subsection.3.16.1}{3.16.1} & 3-56 \\[0.5em]
|
|
Hard disk expansion box & \hyperlink{subsection.3.17.1}{3.17.1} & 3-58 \\[0.5em]
|
|
Keyboard (VAXstation 2000 only) & \hyperlink{section.3.13}{3.13} & 3-51 \\[0.5em]
|
|
Memory module & \hyperlink{section.3.5}{3.5} & 3-17 \\[0.5em]
|
|
Mouse (VAXstation 2000 only) & \hyperlink{section.3.14}{3.14} & 3-52 \\[0.5em]
|
|
Network interconnect module & \hyperlink{section.3.6}{3.6} & 3-18 \\[0.5em]
|
|
Power supply in hard disk expansion box & \hyperlink{subsubsection.3.17.1.2}{3.17.1.2} & 3-66 \\[0.5em]
|
|
Power supply in system box & \hyperlink{section.3.11}{3.11} & 3-64 \\[0.5em]
|
|
Power supply in tape drive expansion box & \hyperlink{subsubsection.3.17.2.3}{3.17.2.3} & 3-79 \\[0.5em]
|
|
RD32 disk drive & \hyperlink{section.3.8}{3.8} & 3-24 \\[0.5em]
|
|
RD32 disk drive device electronics board & \hyperlink{subsection.3.8.1}{3.8.1} & 3-27 \\[0.5em]
|
|
|
|
\end{tbl}
|
|
|
|
\begin{tblcont}{FRU Section Listings}{l l l}
|
|
\textbf{FRU} & \textbf{Section} & \textbf{Page} \\
|
|
\hline
|
|
|
|
RD53 disk drive & \hyperlink{section.3.7}{3.7} & 3-19 \\[0.5em]
|
|
RD53 disk drive device electronics board & \hyperlink{subsection.3.7.1}{3.7.1} & 3-21 \\[0.5em]
|
|
RD53 disk drive in hard disk expansion box & \hyperlink{subsubsection.3.17.1.1}{3.17.1.1} & 3-60 \\[0.5em]
|
|
Resistor load board in hard disk expansion box & \hyperlink{subsubsection.3.17.1.3}{3.17.1.3} & 3-70 \\[0.5em]
|
|
Resistor load board in system box & \hyperlink{section.3.9}{3.9} & 3-31 \\[0.5em]
|
|
Resistor load board in tape drive expnnsion box & \hyperlink{subsubsection.3.17.2.4}{3.17.2.4} & 3-81 \\[0.5em]
|
|
RX33 floppy disk drive & \hyperlink{section.3.8}{3.8} & 3-24 \\[0.5em]
|
|
System module & \hyperlink{section.3.4}{3.4} & 3-13 \\[0.5em]
|
|
Tablet (VAXstation 2000 only) & \hyperlink{section.3.14}{3.14} & 3-52 \\[0.5em]
|
|
Tape drive expansion box & \hyperlink{subsection.3.17.2}{3.17.2} & 3-72 \\[0.5em]
|
|
Terminal disconnection from MicroVAX 2000 & \hyperlink{section.3.15}{3.15} & 3-53 \\[0.5em]
|
|
TK50 tape drive in tape drive expansion box & \hyperlink{subsubsection.3.17.2.2}{3.17.2.2} & 3-76 \\[0.5em]
|
|
TZK50 Controller board in tape drive expansion box & \hyperlink{subsubsection.3.17.2.1}{3.17.2.1} & 3-73 \\[0.5em]
|
|
VR260 deflection board & \hyperlink{subsection.3.12.2}{3.12.2} & 3-39 \\[0.5em]
|
|
VR260 monochrome monitor & \hyperlink{section.3.12}{3.12} & 3-35 \\[0.5em]
|
|
VR260 power LED & \hyperlink{subsection.3.12.7}{3.12.7} & 3-50 \\[0.5em]
|
|
VR260 rear bulkhead assembly & \hyperlink{subsection.3.12.3}{3.12.3} & 3-42 \\[0.5em]
|
|
VR260 transformer assembly & \hyperlink{subsection.3.12.5}{3.12.5} & 3-45 \\[0.5em]
|
|
VR260 video board & \hyperlink{subsection.3.12.4}{3.12.4} & 3-44 \\[0.5em]
|
|
VR260 tube/yoke/bezel assembly & \hyperlink{subsection.3.12.6}{3.12.6} & 3-47 \\[0.5em]
|
|
\end{tblcont}
|
|
|
|
\newpage
|
|
|
|
\figref{3-1} shows the locations of the FRUs as seen from the front.
|
|
|
|
\fig{MA-0133+0150-87}{FRU Locations}
|
|
|
|
\newpage
|
|
|
|
\section{Shield Removal}
|
|
|
|
\begin{enumerate}
|
|
|
|
\item Turn the system power switch off and disconnect all cables from the
|
|
rear of the system box.
|
|
|
|
\item If the system is a MicroVAX 2000, remove the DEC423 converter from
|
|
the rear of the system box.
|
|
|
|
\item If the expansion adapter is installed, then remove the two screws shown
|
|
in \figref{3-2} on the bottom of the expansion adapter to access the four
|
|
screws securing the system box cover.
|
|
|
|
\fig{MA-0069-87}{Expansion Adapter Cover Screw Locations}
|
|
\newpage
|
|
|
|
\item Remove the four system box cover screws shown in \figref{3-3}.
|
|
|
|
\fig{MA-0070-87}{System Box Cover Screw Locations}
|
|
\newpage
|
|
|
|
\item Slide the cover off the system box as shown in \figref{3-4}.
|
|
|
|
\fig[0.6]{MA-0071-87}{System Box Cover Removal}
|
|
\newpage
|
|
|
|
\item Put the system on its feet and remove the five screws shown in
|
|
\figref{3-5} from the shield.
|
|
|
|
\fig{MA-0072-87}{Shield Screw Locations}
|
|
\newpage
|
|
|
|
\item Lift the shield as shown in \figref{3-6} and rest it on the rear of the
|
|
system.
|
|
|
|
\fig{MA-0073-87}{Removing the Shield from the Main Chassis}
|
|
\newpage
|
|
|
|
\item Hold the shield with one hand and disconnect the power cable and the
|
|
drive interconnect cable(s) from the shield with the other hand. Refer
|
|
to \figref{3-7}.
|
|
|
|
\fig[0.9]{MA-0074-87}{Disconnecting the Cables from the Shield}
|
|
|
|
\item Lift the shield off the main chassis.
|
|
|
|
\item Return to the FRU removal instructions that sent you to this procedure.
|
|
\end{enumerate}
|
|
|
|
\newpage
|
|
|
|
\section{System Module Assembly Removal from Shield}
|
|
|
|
\begin{enumerate}
|
|
|
|
\item Remove the two screws shown in \figref{3-8} from the shield.
|
|
|
|
\fig{MA-0075-87}{System Module Assembly Screw Locations on the Shield}
|
|
\newpage
|
|
|
|
\item Disconnect the two network interconnect cable9 shown in \figref{3-9}
|
|
(if installed).
|
|
|
|
\fig{MA-0076-87}{Network Interconnect Cables}
|
|
\newpage
|
|
|
|
\item Remove the system module assembly from the shield as shown in
|
|
\figref{3-10} and lay it down beside the shield.
|
|
|
|
\caution{Disconnection of the battery cable from the system module destroys
|
|
all NVR memory. Be careful not to disconnect the battery cable from the system
|
|
module until a procedure specifically instructs you to do so.}
|
|
|
|
\fig{MA-0077-87}{Removing System Module Assembly from Shield}
|
|
\end{enumerate}
|
|
|
|
\newpage
|
|
|
|
\section{System Module Removal}
|
|
|
|
\begin{itemize}
|
|
|
|
\item Remove the shield (\hyperlink{section.3.2}{Paragraph 3.2}).
|
|
|
|
\item Remove the system module assembly from the shield (\hyperlink{section.3.3}{Paragraph 3.3}).
|
|
|
|
\item Disconnect the battery cable from the system module. Refer to \figref{3-11}.
|
|
|
|
\fig{MA-0078-87}{Battery Cable Location}
|
|
\newpage
|
|
|
|
\item Remove the memory module (if installed). Refer to \figref{3-12}. Two
|
|
connectors disconnect as you lift the memory module.
|
|
\fig{MA-0079-87}{Memory Module Removal}
|
|
|
|
\item Remove the two network interconnect cables from the system module
|
|
and install them on the new system module.
|
|
|
|
\newpage
|
|
|
|
\item Remove the network ID ROM shown in \figref{3-13} from the system
|
|
module you are removing and install it on the system module you are
|
|
installing.
|
|
\fig{MA-0080-87}{Network ID ROM Location on System Module}
|
|
\newpage
|
|
|
|
\item You must set the system jumper, shown in \figref{3-14}, for either a
|
|
VAXstation 2000 or a MicroVAX 2000. Both systems use the same
|
|
system module and this system jumper teils the firmware whether the
|
|
module is in a VAXstation 2000 or a MicroVAX 2000. Determine which
|
|
system you are working on and set the jumper accordingly.
|
|
\fig{MA-0081-87}{VAXstation 2000 and MicroVAX 2000 System Jumper}
|
|
|
|
\item Install the new system module by reversing the above procedures.
|
|
|
|
\end{itemize}
|
|
|
|
\newpage
|
|
|
|
\section{Memory Module Removal}
|
|
|
|
\begin{enumerate}
|
|
|
|
\item Remove the shield (\hyperlink{section.3.2}{Paragraph 3.2})
|
|
|
|
\item Remove the system module assembly from the shield (\hyperlink{section.3.3}{Paragraph 3.3})
|
|
|
|
\item Remove the memory module shown in \figref{3-15}. Two connectors
|
|
disconnect as you lift the module.
|
|
|
|
\fig{MA-0079-87}{Memory Module Removal}
|
|
|
|
\item Replace the memory module by reversing the above procedures.
|
|
|
|
\end{enumerate}
|
|
\newpage
|
|
|
|
\section{Network Interconnect Module Removal}
|
|
\begin{enumerate}
|
|
|
|
\item Remove the shield (\hyperlink{section.3.2}{Paragraph 3.2})
|
|
|
|
\item Remove the system module assembly from the shield (\hyperlink{section.3.3}{Paragraph 3.3})
|
|
|
|
\item Remove the network interconnect module from the shield as shown in \figref{3-16}.
|
|
|
|
\fig{MA-0082-87}{Network Interconnect Module Removal}
|
|
|
|
\item Replace the network interconnect module by reversing the above procedures.
|
|
\end{enumerate}
|
|
|
|
\newpage
|
|
|
|
\section{RD53 Hard Disk Drive Removal from System Box}
|
|
|
|
\begin{enumerate}
|
|
|
|
\item Remove the shield (\hyperlink{section.3.2}{Paragraph 3.2})
|
|
|
|
\item Remove the three screws shown in \figref{3-17} that secure the drive to
|
|
the chassis.
|
|
|
|
\fig{MA-0083-87}{Hard Disk Screw Locations}
|
|
|
|
\newpage
|
|
|
|
\item Slide the drive out halfway and disconnect the drive interconnect cables
|
|
and the power cable from the drive as shown in \figref{3-18}.
|
|
|
|
\fig{MA-0125-87}{Disconnecting the Hard Disk Drive from System Box}
|
|
|
|
\item Slide the drive out of the chassis.
|
|
|
|
\newpage
|
|
|
|
\item Remove two screws on each side of the drive mounting brackets shown
|
|
in \figref{3-19}. Remove the mounting brackets and front panels from
|
|
the drive.
|
|
|
|
\fig[0.8]{MA-0084-87}{Drive Mounting Bracket Screw Locations}
|
|
|
|
\item If you removed the RD53 because of an error with the drive, go to
|
|
\hyperlink{section.3.7.1}{Paragraph 3.7.1}.
|
|
|
|
\item Reverse the above procedures to replace the drive.
|
|
\end{enumerate}
|
|
|
|
\subsection{RD53 Disk Drive Device Electronics Board Removal}
|
|
|
|
The RD53 disk drive has an FRU inside it. It is the device electronics board.
|
|
Always replace the device electronics board on the RD53 before you replace
|
|
an entire RD53 disk drive.
|
|
|
|
\begin{enumerate}
|
|
|
|
\item If a skid plate is installed on the drive, remove the four phillips screws
|
|
securing the skid plate and ground clip to the frame. Remove the plate
|
|
and set aside.
|
|
|
|
\item Loosen the two captive screws that hold the device electronics board in
|
|
place and then disconnect the ground wire.
|
|
|
|
\item Rotate the board upward as shown in \figref{3-20} (the board pivots in
|
|
hinged slots at the front of the drive). Be careful not to strain any of
|
|
the connectors or cables, and tilt the board up and back until it rests
|
|
against the outer frame.
|
|
|
|
\caution{Flexible cirant material is fragile and requires careful handling to
|
|
avoid damage.}
|
|
|
|
\fig{SHA-0134-85}{RD53 Device Electronics Board Removal}
|
|
|
|
\item Disconnect the two connectors from under the device electronics board.
|
|
Both connectors and cables are fragile, handle them with care.
|
|
|
|
\item Lift the board out of the hinged slots.
|
|
|
|
\newpage
|
|
|
|
\item Position the jumpers and switches on the new board to the same
|
|
Remove the shield (\hyperlink{section.3.2}{Paragraph 3.2})
|
|
|
|
position as the jumpers and switches on the old board you just removed.
|
|
Refer to \figref{3-21}. Also be sure the new board has the resistor
|
|
terminator pack installed.
|
|
|
|
\fig{SHR-0126-85}{RD53 Device Electronics Board Jumper and Switch Locations}
|
|
|
|
\item Install the replacement device eiectronics board by reversing the above procedure.
|
|
|
|
\end{enumerate}
|
|
|
|
\newpage
|
|
|
|
\section{RX33 and RD32 Drive Removal (Half-Height Drives) from the System Box}
|
|
|
|
\begin{enumerate}
|
|
|
|
\item Remove the shield (\hyperlink{section.3.2}{Paragraph 3.2})
|
|
|
|
\item Remove the three screws shown in \figref{3-22} that hold the drive(s) to
|
|
the chassis.
|
|
|
|
\fig[0.9]{MA-0085-87}{Half-Height Drive(s) Screw Locations}
|
|
\newpage
|
|
|
|
\end{enumerate}
|